Pachislo cr code error

[TerryLee]

4A8D8583-A8D7-489A-8249-8B0FD4B5A352.jpg

[TerryLee]

46C9AB64-FD7A-4926-A404-3AC5A70761D4.jpg21DEF991-6E5E-4386-851C-57A054BCC850.jpg46C9AB64-FD7A-4926-A404-3AC5A70761D4.jpg21DEF991-6E5E-4386-851C-57A054BCC850.jpg46C9AB64-FD7A-4926-A404-3AC5A70761D4.jpg21DEF991-6E5E-4386-851C-57A054BCC850.jpg46C9AB64-FD7A-4926-A404-3AC5A70761D4.jpg21DEF991-6E5E-4386-851C-57A054BCC850.jpg

[TerryLee]

Link to video coming soon, I hope ��

[TerryLee]

Link to video. http://www.youtube.com/@terrycook1192. No period at the end and all lower case.

[takethecastle57]

4A8D8583-A8D7-489A-8249-8B0FD4B5A352.jpg

I see a empty socket do you have a missing cable ?

[TerryLee]

Yeah I noticed that too. That’s the way it came. I have no idea what goes there. Also it didn’t have an over flow container.

[Drunkenclam]

打ち止め it roughy translates to [stop]

are all the stop levers, buttons etc connected?

The overflow tub if you have one (not the most important) on all of my machines is wired to the main PSU

[TerryLee]

Yeah, all my stop levers are connected. I’ll try to post pictures of the empty jack but even if there was a cable hooked there, I can’t see where the other end would hook to. I’ll also get a picture of the empty over flow area.

[TerryLee]

3872E4E3-9B7E-41DB-814E-7117BC71112A.jpg3872E4E3-9B7E-41DB-814E-7117BC71112A.jpg

[TerryLee]

FAF5D6BB-E10D-4DFD-918B-27962AC83655.jpg

[Drunkenclam]

Is there a switch/sensor in the door lock mechanism.

[TerryLee]

Is there a switch/sensor in the door lock mechanism.

Yes. I’ll post a picture.

[TerryLee]

0C94C1BD-27F1-43B6-A893-7E9CE599505F.jpeg

[Drunkenclam]

Anyone got a Bellco they can compare with?

[TerryLee]

Hey guys, I was wondering if anyone could post a picture of the inside of the door of a Bellco type B. Preferably a shot like in the one in #33 of this thread. Thanks

[atlanticom]

My Bellco Double Chance may be similar. Here's a picture per your request:
IMG_1954.JPG

FYI: Yes, that's a big paper clip holding the plastic door in place...

[atlanticom]

Looking at my wiring (and the code for my arduino coin-up mod) and remembering a little bit of the past... I believe the left-most socket of my Bellco was originally empty and the 2nd socket was connected to the photo-switch for soft reset. However, in my case, I connected the second socket wires to my arduino for power and soft-reset functionality, leaving the other (left-most) connector available. I recall it also provided some reset functionality, but I'm not sure at the moment. Long story short, I think the empty socket is probably normal.

[TerryLee]

Thanks for the picture and yes, it looks like mine is different. My left most socket is empty and the second from the left is connected to the door latch. He didn't say anything about a cable being missing. I did just noticed a sensor on the door latch that I didn't clean. On it now.

[TerryLee]

When you drop a coin in with the door open, you can hold it in different places along the acceptor. Everything is fine until it goes between the split sensor. That's where it sets off the code error.

[Drunkenclam]

Yep. It’s probably a broken sensor.