Results 1 to 9 of 9

Thread: Video of my solution for pachinkos with dead CRTs

  1. #1
    Fever Hunter judremy's Avatar
    Join Date
    Aug 2019
    Location
    Michigan
    Posts
    121
    Thanks
    114
    Thanks Received
    154

    Default Video of my solution for pachinkos with dead CRTs

    Check out my video here for my POC. Took a little time to figure out, but I was determined as I bought a machine with a dying (now dead) CRT.


  2. The following 11 users say "Thanks" to judremy


  3. #2
    Stuey - The RADministrator MrGneiss's Avatar
    Join Date
    Apr 2005
    Location
    Indianapolis, IN
    Posts
    39,648
    Thanks
    69,098
    Thanks Received
    46,225

    Default Re: Video of my solution for pachinkos with dead CRTs

    That is super Rad!! I think I'll make this thread a Sticky in the Modern Pachinko forum!!


    "Blowing smoke rings at the moon."

  4. The following 3 users say "Thanks" to MrGneiss


  5. #3
    Pachi Puro Peteybob's Avatar
    Join Date
    May 2013
    Location
    Grand Rapids, Michigan
    Posts
    6,055
    Thanks
    6,592
    Thanks Received
    3,735

    Default Re: Video of my solution for pachinkos with dead CRTs

    Very cool! Thanks for your time and effort in figuring this out.

  6. The following user says "Thanks" to Peteybob


  7. #4
    Fever Hunter judremy's Avatar
    Join Date
    Aug 2019
    Location
    Michigan
    Posts
    121
    Thanks
    114
    Thanks Received
    154

    Default Re: Video of my solution for pachinkos with dead CRTs

    Quote Originally Posted by MrGneiss View Post
    That is super Rad!! I think I'll make this thread a Sticky in the Modern Pachinko forum!!
    Thank you for doing that. I will be posting more information including the conversion board I bought, connector sizes to make a cable that can connect to both ends (instead of the jumpers), and the TFT LCD that I will put in the machine. I'll also confirm if you can have two monitors going at the same time and post a video with my findings.

  8. The following 3 users say "Thanks" to judremy


  9. #5
    Fever Hunter judremy's Avatar
    Join Date
    Aug 2019
    Location
    Michigan
    Posts
    121
    Thanks
    114
    Thanks Received
    154

    Default Re: Video of my solution for pachinkos with dead CRTs

    I have received and added the LCD to the solution. In the video below, you can see that I don't have the LCD mounted yet, but I sat it in the pachinko so you can get an idea of how it looks. I do go over the setup and connections.


  10. The following 5 users say "Thanks" to judremy


  11. #6
    Chicken Fried Steak takethecastle57's Avatar
    Join Date
    Aug 2005
    Location
    Monterey , Ca
    Posts
    21,922
    Thanks
    27,287
    Thanks Received
    12,229

    Default Re: Video of my solution for pachinkos with dead CRTs

    That is pure Perseverance
    When things don't go right the 1st time , Step back ,Take a break and come back renewed. RGS

  12. The following user says "Thanks" to takethecastle57


  13. #7
    Tokie Owens NicoleExpress's Avatar
    Join Date
    Dec 2022
    Location
    New England
    Posts
    29
    Thanks
    33
    Thanks Received
    44

    Default Re: Video of my solution for pachinkos with dead CRTs

    I had never seen this machine before, and I love the theme; good work saving it! This is a great solution.

    I hang out in the retro video game scene and people there have created a custom firmware for these GBS-8200 boards: https://github.com/ramapcsx2/gbs-control . I think it's overkill for a pachinko machine (those frames of lag aren't going to be noticeable, and the screen is too small to need the image quality boost), but it should get rid of the flash of Chinese characters if that bothers you.

  14. The following user says "Thanks" to NicoleExpress


  15. #8
    Chicken Fried Steak takethecastle57's Avatar
    Join Date
    Aug 2005
    Location
    Monterey , Ca
    Posts
    21,922
    Thanks
    27,287
    Thanks Received
    12,229

    Default Re: Video of my solution for pachinkos with dead CRTs

    Quote Originally Posted by NicoleExpress View Post
    I had never seen this machine before, and I love the theme; good work saving it! This is a great solution.

    I hang out in the retro video game scene and people there have created a custom firmware for these GBS-8200 boards: https://github.com/ramapcsx2/gbs-control . I think it's overkill for a pachinko machine (those frames of lag aren't going to be noticeable, and the screen is too small to need the image quality boost), but it should get rid of the flash of Chinese characters if that bothers you.


    and biscuits
    When things don't go right the 1st time , Step back ,Take a break and come back renewed. RGS

  16. The following user says "Thanks" to takethecastle57


  17. #9
    Fever Hunter judremy's Avatar
    Join Date
    Aug 2019
    Location
    Michigan
    Posts
    121
    Thanks
    114
    Thanks Received
    154

    Default Re: Video of my solution for pachinkos with dead CRTs

    I'll be putting up the final video shortly. I know I keep saying that, but life has been crazy for about the last ten months.

  18. The following 4 users say "Thanks" to judremy


Similar Threads

  1. IT'S ALIVE Solution for dead CRTs in older pachinko machines
    By judremy in forum Pachinko Modifications
    Replies: 4
    Last Post: 01-18-2024, 05:25 PM
  2. Replies: 8
    Last Post: 10-24-2020, 02:46 AM
  3. New Pachinkos for May '13!! Ghost Neo, Dead or Alive
    By MrGneiss in forum Modern Pachinko
    Replies: 18
    Last Post: 06-19-2013, 04:45 AM
  4. pachinkos being born video
    By JamesM in forum Modern Pachinko
    Replies: 5
    Last Post: 01-07-2011, 07:21 AM
  5. Lot of Pinballs, Video Games and Pachinkos
    By hanabi in forum eBay - General Auction listings
    Replies: 0
    Last Post: 08-12-2009, 08:21 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •