Sankyo Pachinko Jackpot Actuator

[Pinballrocks]

Hi All,
I have a Sankyo Pachinko that was working fine, But the Jackpot actuator has broken and the balls will no longer pay out.
Does anyone know if I can get a replacement part for this?
Hoping someone can Help.

Thanks Paul.

[takethecastle57]

Nice , Clear Photos of the machine . Front, Back and a photo focused on the trouble area will help us help you .

[Pinballrocks]

[QUOTE=takethecastle57;626242]Nice , Clear Photos of the machine . Front, Back and a photo focused on the trouble area will help us help you .[/QUOTE

[Pinballrocks]

The blue part at the back had the metal bracket attached by a pin but the plastic as broken and metal can not be re attached.

[Pinballrocks]

I was hoping someone was 3d printing them?

[Pinballrocks]

More pics of the broken jackpot actuator

[takethecastle57]

There is a vintage Sankyo pachinko machine for sale on eBay but the price with shipping is over $300

[machgo]

Cruise ebay for parts or parts machines, or get creative and repair the broken area.

There is a 2 part epoxy clay call Apoxie Sculpt--as well as several others--that can be easily formed and hardens without an oven into a solid which is very similar to styrene plastic, the stuff model kits are made of. Check online. It's a little pricey.

JB Weld--and several others--have 2 part epoxy clays that can be formed easily into any shape you want. Look in your hardware store, particularly in the plumbing department and where they sell adhesives. Fairly cheap.

[Pinballrocks]

There is a vintage Sankyo pachinko machine for sale on eBay but the price with shipping is over $300

Thanks for your reply

I will look further into this

[Moparformances]

gorilla 5 min epoxy will get ya fixed.. i have used on on Vintage pachinko plastics for years

squeeze a bit on a pc of cardboard mix it with a tooth pic or the likes. then use the tooth pic to apply a small dot and bond with a minimum of squeezy out

take your time glue the small bits back together. let it set up for 24 hrs, slowly drill the hole back out to the right size and reassemble.. its probably not going to be prefect so ya will have to tweek the metal bar a bit so it works right..

don't put allot of force on any Vintage parts.. if your forcing it your doing it wrong



https://www.amazon.com/Gorilla-Epoxy.../dp/B001Z3C3AG

[SibSr]

Yes, I have seen this part shatter in the same way after becoming brittle with age.
I have been looking for a new 3D printing challenge. Let me see if I can produce something for you. Give me a couple days and I'll post an update here

[Pinballrocks]

Yes, I have seen this part shatter in the same way after becoming brittle with age.
I have been looking for a new 3D printing challenge. Let me see if I can produce something for you. Give me a couple days and I'll post an update here

No worries, sounds good mate. Cheers!

[SibSr]

So I generated a 1.0 model which looked great but didn't function quite right. Version 2.0 was oh so close but after trying it in 3 different machines it was obvious it was 1-2mm off in an important way. So version 3 is being printed now. I expect it to work properly on all 4 of my Sankyos, and then be ready for production.

Pics are version 2.0



Sent from my LG-H872 using Tapatalk

[SibSr]

Here is one of my blue ones that I put metal pins in and then superglued together. I'll be printing one of these payoff rockers for my machine too.

Sent from my LG-H872 using Tapatalk

[SibSr]

This much interference caused it to not refill after a payoff. And alignment was a little worse on an older Sankyo. Version 3 should fix this.

Sent from my LG-H872 using Tapatalk

[SibSr]

Hi All,
I have a Sankyo Pachinko that was working fine, But the Jackpot actuator has broken and the balls will no longer pay out.
Does anyone know if I can get a replacement part for this?
Hoping someone can Help.

Thanks Paul.

Paul, I have your part for you. Would you like me to send one half way around the world to you so we can get your machine going again?
No cost other than shipping charges....

sankyobluerocker3D.jpg

[Pinballrocks]

Yes Please that would be fantastic. Thank you sooo much I was beginning to think the machine would never work again.

Thanks again. Sorry I didn't answer earlier I have been affected by floods.

[Pinballrocks]

I can pay via Pay pal if you like. Just let me know how you want payment. Send me a PM and I will give you postal Address.

[SibSr]

The patched up blue payout rocker I was using as a model fell on the floor and broke in a different place during this process. But I had "no worries", since I had one ready to go into the machine after Paul's request :-)

I also created a 3D copy of the newer style clear payout rocker that replaced the blue ones. There is a small difference between the two. I'll post both .stl files in the 3D parts thread shortly.

[SibSr]

Part is working it's way to Paul in Australia