Results 1 to 15 of 15

Thread: Model 2000 Sankyo Error Code

  1. #1
    Tokie Owens TheWhiteQuacker's Avatar
    Join Date
    Sep 2021
    Location
    Austin
    Posts
    8
    Thanks
    4
    Thanks Received
    7

    Default Model 2000 Sankyo Error Code

    I have a model 2000 Sankyo pachinko machine that I just picked up today. The machine works, and the payouts payout, however, the center jackpot is stuck blinking and beeping. It is giving me an E code where it says open on the machine in the center. Anything would be helpful. I have unplugged the machine in and out a few times and it did not cause the machine to reset.
    IMG_0367.jpg

  2. #2
    Tokie Owens TheWhiteQuacker's Avatar
    Join Date
    Sep 2021
    Location
    Austin
    Posts
    8
    Thanks
    4
    Thanks Received
    7

    Default Re: Model 2000 Sankyo Error Code

    Now I'm still getting still an e code, but instead of just one light being lit down on the bottom its 4, the reels are locking up even when plugged and unplugged to try to reset. No more red flashing lights around the reel or but it is flashing to being lit and not lit. Still beeping.
    IMG_0368.jpg
    Last edited by TheWhiteQuacker; 09-14-2021 at 06:47 PM.

  3. #3
    Tokie Owens TheWhiteQuacker's Avatar
    Join Date
    Sep 2021
    Location
    Austin
    Posts
    8
    Thanks
    4
    Thanks Received
    7

    Default Re: Model 2000 Sankyo Error Code

    And now its back to the first picture and post.

  4. #4
    Pachi Puro Peteybob's Avatar
    Join Date
    May 2013
    Location
    Grand Rapids, Michigan
    Posts
    6,029
    Thanks
    6,576
    Thanks Received
    3,677

    Default Re: Model 2000 Sankyo Error Code

    Hello TheWhiteQuacker and welcome to the group

    In your first picture it looks like you hit a jackpot with the three sevens but I'm not certain as I don't have this game. With a jackpot the lights on the top most likely light up or flash as well. Or least mine does for this frame with a different game cell in it.

    If the trap door labeled "open" is opening and closing then you are in a jackpot round and the lights below it are counting off the 15 or so times this cycles after a certain amount enters it each time.

    I presume that your error comes up due to a lack of balls in the back top hopper? Do you have 500+ balls to play the machine? You will need to keep refilling the back as they payoff in the front. Also if your bottom front tray is overfilled up into the machine this will trigger some machines to stop play until drained off enough. Last thought is you have a ball jam or obstruction not allowing reward balls to payout if this is the case.

  5. The following 3 users say "Thanks" to Peteybob


  6. #5
    Tokie Owens TheWhiteQuacker's Avatar
    Join Date
    Sep 2021
    Location
    Austin
    Posts
    8
    Thanks
    4
    Thanks Received
    7

    Default Re: Model 2000 Sankyo Error Code

    The balls are not the problem. The hopper is full, and the lights at the top aren't flashing, just the ones around the reel and under the open slot. Also, the open slot is not opening and closing. It is just closed. I have played probably 400-500 balls through it, but nothing. Inside the open slot is where the E is. At first I thought it was a jackpot as well, but it wasn't backed up with payouts.

  7. #6
    Tokie Owens TheWhiteQuacker's Avatar
    Join Date
    Sep 2021
    Location
    Austin
    Posts
    8
    Thanks
    4
    Thanks Received
    7

    Default Re: Model 2000 Sankyo Error Code

    At first I thought it was the machine being backed up with payouts. However, I filled the ball hopper and it wasn't needing to make payouts. I started to play it and the payouts were fine for every hole. I played about 500+ balls thought it, and I received my payouts. However I am unable to get the reels to spin when landing in the start hole. The open slot is always closed. No flashing lights at the top, just below open, and around the reel. The E code is inside of the open slot, but I did open it and drop balls into both payout holes, and they did payout.

  8. #7
    Pachi Puro Moparformances's Avatar
    Join Date
    Jan 2009
    Location
    Diamond Springs CA
    Posts
    14,076
    Thanks
    26,525
    Thanks Received
    12,096

    Default Re: Model 2000 Sankyo Error Code

    Welcome to Pachitalk
    Never Doubt that a small group of thoughtful, .......... /........ If your not going to stand behind our troops
    ...committed people can change the world. ............. /.................Please, Please stand in front of them
    .....Indeed, it is the only thing that ever has............./
    .........................................Margaret Mead

  9. #8
    Pachi Puro Moparformances's Avatar
    Join Date
    Jan 2009
    Location
    Diamond Springs CA
    Posts
    14,076
    Thanks
    26,525
    Thanks Received
    12,096

    Default Re: Model 2000 Sankyo Error Code

    how many balls do you have??

    pics of the back of the machine in it current state..

    some machines will error if the machine hits a jackpot/fever if not played threw.. keep in mind this is a gambling machine.. the machine is confused that a plyaer would not continue playing threw a jackpot..

    Im more if a vintage kinda guy but more pics the better.. im sure we can help ya get it working correctly..
    Never Doubt that a small group of thoughtful, .......... /........ If your not going to stand behind our troops
    ...committed people can change the world. ............. /.................Please, Please stand in front of them
    .....Indeed, it is the only thing that ever has............./
    .........................................Margaret Mead

  10. The following user says "Thanks" to Moparformances


  11. #9
    Pachi Puro Peteybob's Avatar
    Join Date
    May 2013
    Location
    Grand Rapids, Michigan
    Posts
    6,029
    Thanks
    6,576
    Thanks Received
    3,677

    Default Re: Model 2000 Sankyo Error Code

    Have a look at this post from the past:

    https://www.pachitalk.com/forums/sho...ht=fever+queen

    Sounds like your same issue and a sensor could be bad or just have a loose wire.

    If you are comfortable with some simple electronics and perhaps soldering then you got this! If you have a need for the sensor then you will want to see what wires are attached and how long they are. I have some of the TL-PP93 sensors available, some bare needing soldering and some with three different wire sets/connections attached.

    Here's a little write up on your machine if you were curious.

    https://www.sankyo-fever.jp/history/...sc%26page%3D10

  12. The following 4 users say "Thanks" to Peteybob


  13. #10
    Chicken Fried Steak takethecastle57's Avatar
    Join Date
    Aug 2005
    Location
    Monterey , Ca
    Posts
    21,240
    Thanks
    26,028
    Thanks Received
    11,934

    Default Re: Model 2000 Sankyo Error Code



    Well it comes down to your cable connectors possibly having corrosion on them .

    With the machine Unplugged , One by One disconnect and reconnect each cable to break the corrosion .

    Having a good work light while you are doing this helps a lot .

    Could you please post nice and clear photo's of the back of the machine on this Thread. Many thanks.
    When things don't go right the 1st time , Step back ,Take a break and come back renewed. RGS

  14. The following user says "Thanks" to takethecastle57


  15. #11
    I was thrown out of Top Gear Drunkenclam's Avatar
    Join Date
    May 2010
    Location
    Guildford, Surrey
    Posts
    28,495
    Thanks
    13,435
    Thanks Received
    18,805

    Default Re: Model 2000 Sankyo Error Code

    Ok. Back up a bit. Just to confirm. When you get a ball in the start pocket. Your getting a 7 ball payout, but no reel spin?
    Ian #UKPachinko

  16. #12
    Tokie Owens TheWhiteQuacker's Avatar
    Join Date
    Sep 2021
    Location
    Austin
    Posts
    8
    Thanks
    4
    Thanks Received
    7

    Default Re: Model 2000 Sankyo Error Code

    Drunkenclam, I get a 7 ball payout every time a ball goes through it, but the reel doesn't spin; however, I know the reel does spin because it spins when you turn the machine on, then it lands on triple 7s to load into the game, and then lights start blinking and the machine starts beeping. I unplugged the wire to the speaker. As for Takethecastle57 it doesn't appear to have any corrosion at all.

    IMG_0370.jpgIMG_0372.jpg

  17. The following user says "Thanks" to TheWhiteQuacker


  18. #13
    Tokie Owens TheWhiteQuacker's Avatar
    Join Date
    Sep 2021
    Location
    Austin
    Posts
    8
    Thanks
    4
    Thanks Received
    7

    Default Re: Model 2000 Sankyo Error Code

    Resolved: Replaced TL-PP93 ball sensor and it is running like a champ. It looks like some sort of cell inside of the sensor burned up.

  19. The following 6 users say "Thanks" to TheWhiteQuacker


  20. #14
    Tokie Owens Random1111's Avatar
    Join Date
    Sep 2022
    Location
    Austin TX
    Posts
    19
    Thanks
    6
    Thanks Received
    10

    Default Re: Model 2000 Sankyo Error Code

    Hi all, I have a Sankyo Fever Queen also that looks to be the same model. I think I'm having the same issue with mine. When I plug it in the wheels spin and then stay on 3 7's. I get an alarm sound and lights flash. The wheels don't spin anymore when a ball goes in the 'Start' pocket. How much disassembly do I need to do to get to that sensor? I was thinking this was some kind of tamper alarm.

  21. #15
    Chicken Fried Steak takethecastle57's Avatar
    Join Date
    Aug 2005
    Location
    Monterey , Ca
    Posts
    21,240
    Thanks
    26,028
    Thanks Received
    11,934

    Default Re: Model 2000 Sankyo Error Code

    and ginger snap cookies
    When things don't go right the 1st time , Step back ,Take a break and come back renewed. RGS

Similar Threads

  1. Sankyo pachinko stellar new 2000 model Great cannon
    By jmneo28 in forum Modern Pachinko
    Replies: 5
    Last Post: 02-24-2020, 04:04 AM
  2. Sankyo Pachinko Machine E-1 error code and no payouts
    By pgianotto in forum Pachinko Technical Support Tickets
    Replies: 14
    Last Post: 05-27-2018, 04:41 PM
  3. Replies: 1
    Last Post: 02-27-2016, 06:43 PM
  4. error code on sammy model
    By thedream in forum Pachislo Technical Support Tickets
    Replies: 5
    Last Post: 06-21-2012, 03:10 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •