Results 1 to 11 of 11

Thread: Battle counter connector help

  1. #1
    Blind Shooter BGTsoccer1's Avatar
    Join Date
    Sep 2020
    Location
    Ottawa, KS
    Posts
    77
    Thanks
    113
    Thanks Received
    42

    Default Battle counter connector help

    I got a couple battle counters from Japan and needing some help with how to possibly find the wire connector for my Rocky machine. The connector I need for the machine is correct for the P plate but the other end is the female end and I guess I need a male to male to connect the p plate to the machine?

    Here is the connector I need:




    Here is the machine inputs:


    Does anyone know what the connector is called or where to get it?

    Thanks!




    Sent from my iPhone using Tapatalk

  2. #2
    Blind Shooter billyp203's Avatar
    Join Date
    Jul 2007
    Location
    SouthWestern CT
    Posts
    76
    Thanks
    18
    Thanks Received
    60

    Default Re: Battle counter connector help

    Do you have a P plate? if yes, then you'll just have to solder the wires to your machine (Unless someone here has spare quick connects) since they will be very hard to find in the States.

    You'll take off the P plate on the 3 connectors on the right side bottom. (CN0/CN2/CN4)

    And then you'll connect on your machine.... well normally it'll be:
    “Big Win” Plug Red: CN4
    “Little Win” Plug Green: CN5 or (CN10)
    “Bonus” Plug Blue: CN3 or (CN9)

    Good Luck

  3. #3
    Blind Shooter BGTsoccer1's Avatar
    Join Date
    Sep 2020
    Location
    Ottawa, KS
    Posts
    77
    Thanks
    113
    Thanks Received
    42

    Default Re: Battle counter connector help

    Quote Originally Posted by billyp203 View Post
    Do you have a P plate? if yes, then you'll just have to solder the wires to your machine (Unless someone here has spare quick connects) since they will be very hard to find in the States.

    You'll take off the P plate on the 3 connectors on the right side bottom. (CN0/CN2/CN4)

    And then you'll connect on your machine.... well normally it'll be:
    “Big Win” Plug Red: CN4
    “Little Win” Plug Green: CN5 or (CN10)
    “Bonus” Plug Blue: CN3 or (CN9)

    Good Luck
    Yeah I have the P plate. Hoping to not have to solder it but I’ll eventually do what I need to do. Hoping someone has a connection that I could put on that fits my machine. The way they shipped the p plates they had the CN3/4/5 filled so I thought they would match up to the machine CN3/4/5 slots. The cables don’t match the colors of red green and blue at all.


    Sent from my iPhone using Tapatalk

  4. #4
    Blind Shooter billyp203's Avatar
    Join Date
    Jul 2007
    Location
    SouthWestern CT
    Posts
    76
    Thanks
    18
    Thanks Received
    60

    Default Re: Battle counter connector help

    Sorry my bad, running from top down on p plate its green, yellow, red. I tag them on the p plates we have.

  5. #5
    Blind Shooter BGTsoccer1's Avatar
    Join Date
    Sep 2020
    Location
    Ottawa, KS
    Posts
    77
    Thanks
    113
    Thanks Received
    42

    Default Re: Battle counter connector help

    Here is my P board and the connectors that won’t fit on my machine. I need the same connectors that fit into the p board to plug into the Rocky pachinko machine.



    Sent from my iPhone using Tapatalk

  6. #6
    Blind Shooter billyp203's Avatar
    Join Date
    Jul 2007
    Location
    SouthWestern CT
    Posts
    76
    Thanks
    18
    Thanks Received
    60

    Default Re: Battle counter connector help

    Your P plate is a different config than the ones I used to.... There should be writing on the outside edge of the plate next to the connectors.... you want these: CN0/CN2/CN4
    they are 2 wire take offs. then just cut off the machine ends and solder. or solder pigtails to the machine for your own quick connects.

    I can dig around or maybe someone here has spare quick connects?

  7. The following user says "Thanks" to billyp203


  8. #7
    Fever Hunter Vikingwiz's Avatar
    Join Date
    Jul 2018
    Location
    Michigan
    Posts
    208
    Thanks
    195
    Thanks Received
    395

    Default Re: Battle counter connector help

    Recently had a similar issue with a few different types of data counters that came in. We've got tons of connectors for all of this. If you'd like I can make you a harness for this purpose if you don't have a crimper and 22awg wire handy.

  9. The following 2 users say "Thanks" to Vikingwiz


  10. #8
    Blind Shooter BGTsoccer1's Avatar
    Join Date
    Sep 2020
    Location
    Ottawa, KS
    Posts
    77
    Thanks
    113
    Thanks Received
    42

    Default Re: Battle counter connector help

    Quote Originally Posted by billyp203 View Post
    Your P plate is a different config than the ones I used to.... There should be writing on the outside edge of the plate next to the connectors.... you want these: CN0/CN2/CN4
    they are 2 wire take offs. then just cut off the machine ends and solder. or solder pigtails to the machine for your own quick connects.

    I can dig around or maybe someone here has spare quick connects?
    Looking at my board I don’t see a CN0. My board seems to start at CN1 which the person I purchased from said a 3 wire from the battle counter goes in and that one fit. Then the others are already plugged into the CN3/4/5. This is my first battle counter so I’m pretty lost. I thought I had read up on a lot but then got these two counters and it’s confusing lol.

    I also don’t know which wires go to the 24v power wires. I have T taps for that but have not tried that part yet.


    Sent from my iPhone using Tapatalk

  11. #9
    Blind Shooter BGTsoccer1's Avatar
    Join Date
    Sep 2020
    Location
    Ottawa, KS
    Posts
    77
    Thanks
    113
    Thanks Received
    42

    Default Re: Battle counter connector help

    Quote Originally Posted by Vikingwiz View Post
    Recently had a similar issue with a few different types of data counters that came in. We've got tons of connectors for all of this. If you'd like I can make you a harness for this purpose if you don't have a crimper and 22awg wire handy.
    That would be awesome. I have so many wires it’s all confusing. I bought 2 of the counters one for this Rocky Pachinko and then in Nov/Dec I’m getting a 2019 machine Captain Tsubasa from Modern Pachinko so I think the new machine will be set up different on the connectors. If there is anything you need pics of or info from the wires I got please let me know but that would be awesome to get harnesses for these that are just for what we need rather than the mess of wires for a parlor.


    Sent from my iPhone using Tapatalk

  12. #10
    Blind Shooter BGTsoccer1's Avatar
    Join Date
    Sep 2020
    Location
    Ottawa, KS
    Posts
    77
    Thanks
    113
    Thanks Received
    42

    Default Re: Battle counter connector help

    Quote Originally Posted by BGTsoccer1 View Post
    That would be awesome. I have so many wires it’s all confusing. I bought 2 of the counters one for this Rocky Pachinko and then in Nov/Dec I’m getting a 2019 machine Captain Tsubasa from Modern Pachinko so I think the new machine will be set up different on the connectors. If there is anything you need pics of or info from the wires I got please let me know but that would be awesome to get harnesses for these that are just for what we need rather than the mess of wires for a parlor.


    Sent from my iPhone using Tapatalk
    Hey I just looked at your profile I guess I’m getting Tsubasa from you!


    Sent from my iPhone using Tapatalk

  13. #11
    Blind Shooter billyp203's Avatar
    Join Date
    Jul 2007
    Location
    SouthWestern CT
    Posts
    76
    Thanks
    18
    Thanks Received
    60

    Default Re: Battle counter connector help

    I'm passing you on to Brandon @ Modern. Since he has your machine, he can ensure you've got the right connectors!
    Good Luck & Enjoy,
    Bill

  14. The following user says "Thanks" to billyp203


Similar Threads

  1. WTB Battle Counter in the US
    By MGB1977 in forum Members Trade area
    Replies: 2
    Last Post: 09-10-2016, 06:14 PM
  2. Battle counter
    By Pachinko Botan in forum Yahoo Japan - Auction Area
    Replies: 11
    Last Post: 03-03-2016, 01:39 PM
  3. Needed 10 Way Battle Counter Connector and Pin Out for Heiwa Hotaru Frame
    By Cris in forum Pachinko Technical Support Tickets
    Replies: 6
    Last Post: 10-25-2015, 11:53 AM
  4. Battle Counter Where do I get one???
    By Planedoc in forum Modern Pachinko
    Replies: 9
    Last Post: 04-28-2010, 09:42 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •