Bulbs for Lumina frame

[Dr.Phil]

I researched , I called , I Emailed, and I still can not locate bulbs for a Lumina frame, which are located on top between the speakers. Please Help me .

[arbycoffee]

What color or colors you need ?

[Dr.Phil]

It is for a Julie Pachinko, and I need both Red and White. From what I can tell they are clear with red and blue covers over them.

I thank You

[arbycoffee]

It is for a Julie Pachinko, and I need both Red and White. From what I can tell they are clear with red and blue covers over them.

I thank You

There are Clear LEDs, Red LEDs, and Blue LEDs in that case front window.

[drcrippen324]

he isnt thinking of the bonus lights red white red white red white is he in an ark above teh glass ???

[arbycoffee]

I think that too is what he is asking and there are the Red, Clear and blue there

[drcrippen324]

ahhhhahhhh i see

[arbycoffee]

I wish I see naked women , but it is too cold here



I need coffee

[Dr.Phil]

ahhhhahhhh i see

Yes that is the lights I'm talking about.

he isnt thinking of the bonus lights red white red white red white is he in an ark above teh glass ???

Yes those are the lights I'm talking about.
Sorry for the double post

[deton8r]

If you're talking about the ones that twist in with the rubber covers, you can use the 2 wire bulbs from slot-pachinko. I was able to disassemble them and replace the bulbs. All I needed was a pin or needle and some patience. The slot-pachinko bulbs were slightly smaller but work fine. Parts Express sells bulbs and the rubber covers that will work as well.

[Dr.Phil]

If you're talking about the ones that twist in with the rubber covers, you can use the 2 wire bulbs from slot-pachinko. I was able to disassemble them and replace the bulbs. All I needed was a pin or needle and some patience. The slot-pachinko bulbs were slightly smaller but work fine. Parts Express sells bulbs and the rubber covers that will work as well.

Thanks for the help. If you look in the Auction section, Robocourier has a great deal on the original bulbs with holders. Mine are on there way.

[Chrisdice]

Is there a bulb number so these can be order localy? ex. 400's or 88's like the pachislos use?

[Youngjedi]

I have 6 holders with bad bulbs in them. I hate to through them away, and I like to tinker around with fixing them. Is there a part number from Parts express for the bulbs?

[StuTalon]

Looks like I need some bulbs....

Today I stripped down the entire lumina front case and cleaned every nook and cranny of any remaining smoke, dirt, and general gunk. While that was fairly easy, when I reassembled the frame, only one of the bonus lights decided to work. I took that bulb and rotated it around the arc to see if it was the bulb or the board itself and it looks like every red and blue bulb save that one is no longer working as the good bulb worked in every spot on the frame. I was careful to remove them and place them in a plastic bag. So are they that fragile? Seems weird that I would blow almost 9 bulbs all at once??

[chmer01]

There are some up for auction right now:

http://www.pachitalk.com/auction/Lum...auctiondetails

[luckydog]

check your wiring, maybe just a poor connection.

I had 1/2 of a circle of leds that stopped working and it was just a poor connection

[StuTalon]

check your wiring, maybe just a poor connection.

I had 1/2 of a circle of leds that stopped working and it was just a poor connection

Yea I thought it might be a connection at first, so I took the one good bulb and popped it in each hole on the board, but it worked in every one, so it seems I blew out all but one bulb while removing them.... I never thought they would be this fragile, guess I need to be extra careful from now on.

[luckydog]

they could be like the newer auto bulbs, that the oil from your fingers gets on them and causes them to burn out.

it's possible you may need to wear gloves removing them and replacing them????

[johnnyabc]

stu talon, what did you use to clean the machine?

[StuTalon]

For the plastic, plastic chrome, and plexi I used a watered down 1:1 Oxyclean water mix on a lintless white cloth. All the circuit boards were removed and set aside for the top and side light boards. It did a great job and the frame now shows off the speckled fleck instead of the dulled white it arrived as. It took an hour or so, but keeping all the screws marked made reassembly a snap. Odd that while I removed all the bulbs, only a select few from the top stopped working. The bulb surface was never touched, just the black plastic holder - and these have the colored condom so there was even more protection in that case.