Results 1 to 4 of 4

Thread: Repair issue questions.

  1. #1
    Blind Shooter Spear's Avatar
    Join Date
    Apr 2018
    Location
    Gilroy CA
    Posts
    58
    Thanks
    12
    Thanks Received
    84
    Groans Given
    0
    Groaned 0 Times in 0 Posts

    Default Repair issue questions.

    I've run into 2 issues with the machine I'm currently working on, curious to see what everyone's solutions are for these.

    1) nail broken off - I was replacing nails after polishing them, and found one of the holes had a piece of a nail still in it. As I didn't break a nail, I'm assuming it was broken before I got it.
    As it's up in the upper right corner, I may just drive a replacement nail right next to it, but has anyone been able to extract a nail in this condition?

    2) chrome is gone - This machine must of been in a costal town, the wood and background showed little to no water damage, but everything was heavily corroded. Main issues are with the lever and the finger rest, I've cleaned the rust off them, but they're already starting to oxidize again. I was thinking of cleaning them up again, and then putting some sort of clear coat on them before the can turn again. Short of re-chroming the parts, does anyone have any other suggestions?

  2. #2
    Blind Shooter machgo's Avatar
    Join Date
    Sep 2017
    Location
    Chicago
    Posts
    71
    Thanks
    33
    Thanks Received
    93
    Groans Given
    0
    Groaned 1 Time in 1 Post

    Default Re: Repair issue questions.

    Possibly a pointy and sharp pair of side cutters can grab the nail. The wood would probably take some damage. Any damage could be filled with any number of different readily available products.

    As for the chrome, maybe an automotive lacquer--but good luck getting anything to look like actual chrome.

  3. #3
    Pachi Puro Moparformances's Avatar
    Join Date
    Jan 2009
    Location
    Diamond Springs CA
    Posts
    12,179
    Thanks
    23,448
    Thanks Received
    10,689
    Groans Given
    678
    Groaned 160 Times in 105 Posts

    Default Re: Repair issue questions.

    use a small punch and push the nail threw..

    powder coat the frame in a corresponding dolor to the tray or playfield..
    Never Doubt that a small group of thoughtful, .......... /........ If your not going to stand behind our troops
    ...committed people can change the world. ............. /.................Please, Please stand in front of them
    .....Indeed, it is the only thing that ever has............./
    .........................................Margaret Mead

  4. #4
    Fever Hunter Rumpled's Avatar
    Join Date
    Jun 2018
    Location
    New Jersey
    Posts
    214
    Thanks
    328
    Thanks Received
    234
    Groans Given
    15
    Groaned 2 Times in 2 Posts

    Default Re: Repair issue questions.

    I did the punch.

    I had a machine where the field wood delaminated quite a bit when I took out the nails. Joy! I was able to slather that baby up with wood glue in all the layers and clamp it, but it took a several tries to get the layers back and stable. I knew the field nail holes would be filled with glue and screwing them down was going to be hard. What I did not think about was the races holes were also filled in some places and then poking the wires through was impossible. I messed up my cel when I had to drill (even with a tiny tiny drill bit). So if you are fighting with the nails, and your board delaminates, and you have to glue... drill your races hole before you put on your cel.
    Jewelry Metalworking, Chainmaille, Pachinko
    Pliers make me happy

  5. The following user says "Thanks" to Rumpled


Similar Threads

  1. Replies: 8
    Last Post: 01-17-2017, 11:19 AM
  2. Questions about new machine... or AKA EPIC Noob questions!!
    By stampeed valkyrie in forum Modern Pachinko
    Replies: 17
    Last Post: 05-28-2015, 12:25 PM
  3. Another Matrix issue help needed please screen graphic glitch issue
    By ryantiger99 in forum Pachinko Technical Support Tickets
    Replies: 38
    Last Post: 01-11-2014, 10:37 AM
  4. K1 (LCD) Set up issue
    By dnketc in forum Pachislo Modifications
    Replies: 21
    Last Post: 06-14-2005, 12:48 PM
  5. legal issue
    By Urban Archaeologist in forum Vendors & Manufacturers Pachislo
    Replies: 14
    Last Post: 01-26-2005, 08:28 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •