Results 1 to 7 of 7

Thread: Candy Dispenser turned Ball Dispenser

  1. #1
    Pachi Puro Peteybob's Avatar
    Join Date
    May 2013
    Location
    Grand Rapids, Michigan
    Posts
    4,638
    Thanks
    4,509
    Thanks Received
    2,474

    Default Candy Dispenser turned Ball Dispenser

    I picked up a new (to me) item for my arcade life tonight. It is a free to use or coin-less candy dispenser with four separate slots and it lights up. A cool looking item that I'm thinking of using as a pachinko ball dispenser. The weight of the balls in the picture binds up the turning mechanisms somewhat so I won't fill it any further yet. A bit of testing and engineering thinking is needed!

    This stands 54" tall and is 15" wide by 16" deep and very light weight when empty. There is some nice pin striping on the sides with a storage area on the right side. The top lifts up for loading and the complete inner shell lifts out for cleaning, etc. It still needs a little cleaning and lights to be checked but I think this was a good find on Craig's List only an hour after being posted yesterday.

    I have often wanted to modify a gumball machine of a few different styles but the prices always put a hold on that. This was about the same cost if not less than most gumball types in my area so it was an easy decision to make.

    candy disp a.jpgcandy disp b.jpgcandy disp c.jpgcandy disp d.jpgcandy disp e.jpg

  2. The following 5 users say "Thanks" to Peteybob


  3. #2
    Stuey - The RADministrator MrGneiss's Avatar
    Join Date
    Apr 2005
    Location
    Indianapolis, IN
    Posts
    27,812
    Thanks
    57,088
    Thanks Received
    36,607

    Default Re: Candy Dispenser turned Ball Dispenser

    Cool!!

    "Blowing smoke rings at the moon."

  4. The following user says "Thanks" to MrGneiss


  5. #3
    I was thrown out of Top Gear Drunkenclam's Avatar
    Join Date
    May 2010
    Location
    Guildford, Surrey
    Posts
    23,553
    Thanks
    11,244
    Thanks Received
    15,236

    Default Re: Candy Dispenser turned Ball Dispenser

    Good idea
    Ian #UKPachinko

  6. The following user says "Thanks" to Drunkenclam


  7. #4
    Pachi Puro Moparformances's Avatar
    Join Date
    Jan 2009
    Location
    Diamond Springs CA
    Posts
    12,399
    Thanks
    23,891
    Thanks Received
    10,838

    Default Re: Candy Dispenser turned Ball Dispenser

    nice looking

    can you post a picture of one of the slots empty? would like to see the mechanism. i think i have an easy fix for the weight issue.
    Never Doubt that a small group of thoughtful, .......... /........ If your not going to stand behind our troops
    ...committed people can change the world. ............. /.................Please, Please stand in front of them
    .....Indeed, it is the only thing that ever has............./
    .........................................Margaret Mead

  8. The following user says "Thanks" to Moparformances


  9. #5
    Pachi Puro Peteybob's Avatar
    Join Date
    May 2013
    Location
    Grand Rapids, Michigan
    Posts
    4,638
    Thanks
    4,509
    Thanks Received
    2,474

    Default Re: Candy Dispenser turned Ball Dispenser

    The candy or balls in this case look like they bind up in the mech as the cylinder edge turns toward the compartment wall. It eventually turns by rocking the turn knob back and forth but this would cause damage in time. This is even with the smallest amount of balls loaded. I'll see if a cylinder will come out for a better look. This would be cool to dispense tokens as well but that sounds like a tough one to accomplish. The dividers also come out which is nice for cleaning.

    candy mech a.jpgcandy mech b.jpg

    Here is a Google link as well: https://www.google.com/search?tbm=is...&bih=603&dpr=1

  10. The following 2 users say "Thanks" to Peteybob


  11. #6
    Pachi Puro Moparformances's Avatar
    Join Date
    Jan 2009
    Location
    Diamond Springs CA
    Posts
    12,399
    Thanks
    23,891
    Thanks Received
    10,838

    Default Re: Candy Dispenser turned Ball Dispenser

    well the easy answer is a piece of metal bent at a 90.. make it wide enough to span over the center and rest on the rolled edges.. make it short enough so balls and flow around the front and the rear. the metal will disperse the load to the sides, the gaps in the front and back will allow balls to flow..
    Never Doubt that a small group of thoughtful, .......... /........ If your not going to stand behind our troops
    ...committed people can change the world. ............. /.................Please, Please stand in front of them
    .....Indeed, it is the only thing that ever has............./
    .........................................Margaret Mead

  12. The following 3 users say "Thanks" to Moparformances


  13. #7
    Sandwich Shooter quester's Avatar
    Join Date
    Aug 2010
    Location
    Seattle WA
    Posts
    401
    Thanks
    295
    Thanks Received
    393

    Default Re: Candy Dispenser turned Ball Dispenser

    that's a good idea, i have this item also, i fill with candy and nuts, i also have a popcorn machine version, which doesn't work very well, but I could put balls in that one. They have similar plastic as pachinkos, so makes room look better
    2016 Superman Limit/Blast 2016 Majestic Prince 2015 Macross Frontier 2 2015 Castlevania 2013 Boihazard 2010 Superman Returns 2010 Jurassic Park Max 2 2009 Enter The Matrix 2009 Star Wars 2 Light 2008 Hyper Sea Story plus 12 others

  14. The following 2 users say "Thanks" to quester


Similar Threads

  1. Ball dispenser in cabinet
    By super monkey in forum Pachinko Cabinets
    Replies: 9
    Last Post: 03-21-2018, 08:13 PM
  2. Ball/token dispenser
    By Pachinko Botan in forum Yahoo Japan - Auction Area
    Replies: 2
    Last Post: 01-11-2016, 04:36 PM
  3. Modifying Daito Ball dispenser for electric release
    By Drunkenclam in forum Ball Lifters/Ball Management
    Replies: 10
    Last Post: 01-20-2013, 08:04 PM
  4. My DIY pachinko ball dispenser
    By SteveFury in forum Ball Lifters/Ball Management
    Replies: 0
    Last Post: 03-29-2012, 09:06 PM
  5. Ball dispenser
    By Drunkenclam in forum Yahoo Japan - Auction Area
    Replies: 34
    Last Post: 03-09-2012, 03:47 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •