Page 2 of 2 FirstFirst 1 2
Results 21 to 32 of 32

Thread: Ball lifter finally arrived

  1. #21
    Tokie Owens reach's Avatar
    Join Date
    Jan 2015
    Location
    missouri
    Posts
    14
    Thanks
    1
    Thanks Received
    8

    Default Re: Ball lifter finally arrived

    That sounds like a great idea. thanks, I will order one.

  2. #22
    Tokie Owens reach's Avatar
    Join Date
    Jan 2015
    Location
    missouri
    Posts
    14
    Thanks
    1
    Thanks Received
    8

    Default Re: Ball lifter finally arrived

    I just researched it a bit and agree that the dongle will help. thanks

  3. The following 5 users say "Thanks" to reach


  4. #23
    I was thrown out of Top Gear Drunkenclam's Avatar
    Join Date
    May 2010
    Location
    Guildford, Surrey
    Posts
    28,495
    Thanks
    13,442
    Thanks Received
    18,805

    Default Re: Ball lifter finally arrived

    As I said, what wiring does your lifter have.

    Complete ones should have

    1) 100vac Main Cord
    2) Top tank low level start/stop switch
    3) Door/frame open kill switch
    4) if fully complete Electrical dump solenoid (not needed for home use)

    The last lifter I had delivered only had the mains switch and no low level start/stop switch or door open switch.
    This doesn't bother me, because I'm using it as part of a complete system for multiply machines.
    But to run only one machine, it wouldn't be very good.
    Ian #UKPachinko

  5. #24
    Tokie Owens reach's Avatar
    Join Date
    Jan 2015
    Location
    missouri
    Posts
    14
    Thanks
    1
    Thanks Received
    8

    Default Re: Ball lifter finally arrived

    Are they difficult to install? I went to the webpage, I need the card reader, and what kind of card, there were different kinds? It goes to a Eva 8 Much thanks

  6. #25
    I was thrown out of Top Gear Drunkenclam's Avatar
    Join Date
    May 2010
    Location
    Guildford, Surrey
    Posts
    28,495
    Thanks
    13,442
    Thanks Received
    18,805

    Default Re: Ball lifter finally arrived

    You don't need the card reader unit, just the dongle.
    Ian #UKPachinko

  7. The following 2 users say "Thanks" to Drunkenclam


  8. #26
    Kungishi Spyder138's Avatar
    Join Date
    Sep 2014
    Location
    San Jose, CA
    Posts
    1,117
    Thanks
    3,394
    Thanks Received
    1,813

    Default Re: Ball lifter finally arrived

    Quote Originally Posted by reach View Post
    Are they difficult to install? I went to the webpage, I need the card reader, and what kind of card, there were different kinds? It goes to a Eva 8 Much thanks
    Not hard at all. As Clam said, you don't need the reader. Just the dongle will work. All you need to do is unplug your old one and plug in the new one. You might check the back of your machine and make sure it's an actual dongle and that someone didn't semi-permanently attach the dongle parts directly to the machine. I have one machine that a previous owner attached the components and then applied silicon to the whole thing.

  9. The following 2 users say "Thanks" to Spyder138


  10. #27
    Tokie Owens reach's Avatar
    Join Date
    Jan 2015
    Location
    missouri
    Posts
    14
    Thanks
    1
    Thanks Received
    8

    Default Re: Ball lifter finally arrived

    Quote Originally Posted by Spyder138 View Post
    Not hard at all. As Clam said, you don't need the reader. Just the dongle will work. All you need to do is unplug your old one and plug in the new one. You might check the back of your machine and make sure it's an actual dongle and that someone didn't semi-permanently attach the dongle parts directly to the machine. I have one machine that a previous owner attached the components and then applied silicon to the whole thing.
    Don't know what a dongle is. all of my machines came from Clover Collectibles. Is it the three devices plugged into the bottom left, that the card reader plugs into>???

  11. #28
    Tokie Owens reach's Avatar
    Join Date
    Jan 2015
    Location
    missouri
    Posts
    14
    Thanks
    1
    Thanks Received
    8

    Default Re: Ball lifter finally arrived

    So what exactly do I need to order from Dave, just a Card reader emulator, or What is a dongle, I thought it was the card reader. I went to Daves site . What do I order. They don't show a dongle for sale. You guys are great for helping me THANKS REACH

  12. #29
    I was thrown out of Top Gear Drunkenclam's Avatar
    Join Date
    May 2010
    Location
    Guildford, Surrey
    Posts
    28,495
    Thanks
    13,442
    Thanks Received
    18,805

    Default Re: Ball lifter finally arrived

    This is the fellow.

    http://www.pinballdave.com/store/CRE2.html


    All CR machines must have a dongle, even the simple kind or the shooter will not work. So yes. Clover would have supplied you with 3 basic dongles so you can use your machine
    Ian #UKPachinko

  13. The following 3 users say "Thanks" to Drunkenclam


  14. #30
    Tokie Owens reach's Avatar
    Join Date
    Jan 2015
    Location
    missouri
    Posts
    14
    Thanks
    1
    Thanks Received
    8

    Default Re: Ball lifter finally arrived

    THANKS again It is ordered----May need help when it comes. Thanks again from Reach

  15. The following 2 users say "Thanks" to reach


  16. #31
    Pachi Puro Moparformances's Avatar
    Join Date
    Jan 2009
    Location
    Diamond Springs CA
    Posts
    14,076
    Thanks
    26,525
    Thanks Received
    12,096

    Default Re: Ball lifter finally arrived

    Quote Originally Posted by reach View Post
    THANKS again It is ordered----May need help when it comes. Thanks again from Reach
    there great.. simple and easy.. plug and play.. a must have..
    Never Doubt that a small group of thoughtful, .......... /........ If your not going to stand behind our troops
    ...committed people can change the world. ............. /.................Please, Please stand in front of them
    .....Indeed, it is the only thing that ever has............./
    .........................................Margaret Mead

  17. #32
    Tokie Owens reach's Avatar
    Join Date
    Jan 2015
    Location
    missouri
    Posts
    14
    Thanks
    1
    Thanks Received
    8

    Default Re: Ball lifter finally arrived

    Quote Originally Posted by Moparformances View Post
    there great.. simple and easy.. plug and play.. a must have..
    thanks again---

  18. The following user says "Thanks" to reach


Page 2 of 2 FirstFirst 1 2

Similar Threads

  1. Replies: 4
    Last Post: 09-26-2013, 09:32 PM
  2. Ball lifter finally arrived!
    By pachiwall in forum Ball Lifters/Ball Management
    Replies: 2
    Last Post: 07-02-2011, 11:07 PM
  3. My New Black Spiderman Finally Arrived!
    By DugFreez in forum Pinball
    Replies: 9
    Last Post: 07-08-2009, 06:54 AM
  4. New Art Masterpiece has finally arrived!
    By Eddie in forum Modern Pachinko
    Replies: 13
    Last Post: 09-26-2006, 03:50 PM
  5. My first Pachislo......its finally arrived!!
    By DJMAT in forum Model Talk
    Replies: 12
    Last Post: 08-21-2006, 07:12 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •