Results 1 to 11 of 11

Thread: sammy, reels don't stop

  1. #1
    Tokie Owens slider121's Avatar
    Join Date
    Feb 2017
    Location
    texas
    Posts
    7
    Thanks
    0
    Thanks Received
    5

    Default sammy, reels don't stop

    Hello, I need some help please. I have a Sammy Heavy Metal slot "don't know year" and the reels don't stop. I had to replace the 1uf 50v tantalum on the reel stop board, plus I replaced all the zener diodes. The lights light up for stop but when I hit the buttons it keeps spinning, they do stop when timed out. Anyone have any suggestions.
    Thank you

  2. #2
    Goodwill Ambassador luckydog's Avatar
    Join Date
    Nov 2004
    Location
    bradenton, florida
    Posts
    31,487
    Thanks
    13,448
    Thanks Received
    24,112

    Default Re: sammy, reels don't stop

    they should time out after a few mins spinning.

    is your joystick centering after you press it up or down??
    幸運わんわん Luckydog or Yukiwanwan in Japanese

  3. #3
    Tokie Owens slider121's Avatar
    Join Date
    Feb 2017
    Location
    texas
    Posts
    7
    Thanks
    0
    Thanks Received
    5

    Default Re: sammy, reels don't stop

    thank for replying. Yes, the joystick is centered. other than the stop board, where else would the signal come from.

  4. #4
    Pachi Puro Peteybob's Avatar
    Join Date
    May 2013
    Location
    Grand Rapids, Michigan
    Posts
    6,029
    Thanks
    6,576
    Thanks Received
    3,677

    Default Re: sammy, reels don't stop

    Hello slider121 and welcome to the group!

    Have you seen this recent thread about a similar problem? Look at Wayne-Ooo's entry #3 about the reel sensors. These are located in the inner part of each reel.
    http://www.pachitalk.com/forums/pach...wont-stop.html

  5. #5
    Tokie Owens slider121's Avatar
    Join Date
    Feb 2017
    Location
    texas
    Posts
    7
    Thanks
    0
    Thanks Received
    5

    Default Re: sammy, reels don't stop

    I will check it out, thanks

  6. #6
    Tokie Owens slider121's Avatar
    Join Date
    Feb 2017
    Location
    texas
    Posts
    7
    Thanks
    0
    Thanks Received
    5

    Default Re: sammy, reels don't stop

    sensors were fine. I need a schematic to trace back.

  7. #7
    Tokie Owens slider121's Avatar
    Join Date
    Feb 2017
    Location
    texas
    Posts
    7
    Thanks
    0
    Thanks Received
    5

    Default Re: sammy, reels don't stop

    If anyone has a reel stop board out so the solder side can be seen. There are 3 wires were the power goes in. I need to know if 2 of the pins are soldered together I believe it is the grounds. I had bad cold solder joints and someone tried to repair it to no avail. Thank you vey much.

  8. #8
    Tokie Owens slider121's Avatar
    Join Date
    Feb 2017
    Location
    texas
    Posts
    7
    Thanks
    0
    Thanks Received
    5

    Default Re: sammy, reels don't stop

    ok I fixed it. The 3 wires for power to the stop board had bad cold solder joints. I had to make new grids to make a good connection.

  9. The following 5 users say "Thanks" to slider121


  10. #9
    Pachi Puro Peteybob's Avatar
    Join Date
    May 2013
    Location
    Grand Rapids, Michigan
    Posts
    6,029
    Thanks
    6,576
    Thanks Received
    3,677

    Default Re: sammy, reels don't stop

    Glad you could get it working again, congrats!

  11. #10
    Tokie Owens slider121's Avatar
    Join Date
    Feb 2017
    Location
    texas
    Posts
    7
    Thanks
    0
    Thanks Received
    5

    Default Re: sammy, reels don't stop

    Thank You

  12. #11
    I was thrown out of Top Gear Drunkenclam's Avatar
    Join Date
    May 2010
    Location
    Guildford, Surrey
    Posts
    28,495
    Thanks
    13,435
    Thanks Received
    18,805

    Default Re: sammy, reels don't stop

    Sweet
    Ian #UKPachinko

Similar Threads

  1. Sammy Aladdin II, reels will spin but I can't get them to stop?
    By BR549AUTOSALES in forum Pachislo Technical Support Tickets
    Replies: 4
    Last Post: 02-24-2014, 01:29 AM
  2. Just got a Net Kampai game, reels keep spinning, stop buttons won't stop reels
    By BR549AUTOSALES in forum Pachislo Technical Support Tickets
    Replies: 9
    Last Post: 03-24-2013, 06:38 PM
  3. Replies: 1
    Last Post: 12-15-2012, 07:08 PM
  4. Auto stop reels take 30 seconds to stop
    By smoof in forum Pachislo Technical Support Tickets
    Replies: 32
    Last Post: 08-04-2011, 12:31 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •