Results 1 to 3 of 3

Thread: Servo motor lifter

  1. #1
    I was thrown out of Top Gear Drunkenclam's Avatar
    Join Date
    May 2010
    Location
    Guildford, Surrey
    Posts
    28,495
    Thanks
    13,435
    Thanks Received
    18,805

    Default Servo motor lifter

    Now this has arrived. But as of yet due to UK power difference I haven't plugged it in yet, But here is an overview.

    DSC04824_zpszzujo2y2.jpg DSC04825_zps09rrcvma.jpg DSC04830_zpsatpusprc.jpg

    An on/off switch - For switching on and off the power

    DSC04828_zpsjttcb7hq.jpg

    Speed regulator - For adjusting speed

    DSC04829_zpsm6zbh5rp.jpg

    Only one other switch, The ramp down to the gear is a pressure plate, so when there are enough balls, the motor will start. Unlike the silver brand lifter that has a door open switch and a pressure plate in the top ball tank on back of the pachi.

    DSC04831_zpsrkxwwfin.jpg
    Ian #UKPachinko

  2. The following 11 users say "Thanks" to Drunkenclam


  3. #2
    Pachi Puro Moparformances's Avatar
    Join Date
    Jan 2009
    Location
    Diamond Springs CA
    Posts
    14,076
    Thanks
    26,525
    Thanks Received
    12,096

    Default Re: Servo motor lifter

    very cool..
    Never Doubt that a small group of thoughtful, .......... /........ If your not going to stand behind our troops
    ...committed people can change the world. ............. /.................Please, Please stand in front of them
    .....Indeed, it is the only thing that ever has............./
    .........................................Margaret Mead

  4. The following user says "Thanks" to Moparformances


  5. #3
    I was thrown out of Top Gear Drunkenclam's Avatar
    Join Date
    May 2010
    Location
    Guildford, Surrey
    Posts
    28,495
    Thanks
    13,435
    Thanks Received
    18,805

    Default Re: Servo motor lifter

    I have finally had some time to test this lifter and to be honest. This one doesn't work. When its running its a lot quieter than the silver brand (orange) lifters. But on this one there is to much movement on the output shaft and gear. So it rides up and the balls get stuck rather than flowing nicely round. The play is actually on the shaft its self not on the gear. I think I will try to put a support shaft and bearing coming out of the other side of the gear.


    DSC05902.jpgDSC05903.jpgDSC05904.jpg
    Ian #UKPachinko

  6. The following 6 users say "Thanks" to Drunkenclam


Similar Threads

  1. Japan Servo Co, powered ball lifter
    By Drunkenclam in forum Yahoo Japan - Auction Area
    Replies: 9
    Last Post: 02-22-2015, 07:46 AM
  2. Need payout motor
    By kguenther6 in forum Modern Pachinko
    Replies: 2
    Last Post: 08-11-2012, 11:58 AM
  3. USA W-Lifter Pics Coming Soon! Full USA Worm Lifter DIY Write-up
    By WondersPachi in forum Ball Lifters/Ball Management
    Replies: 3
    Last Post: 08-07-2011, 11:05 PM
  4. Motor question
    By mackoftrack in forum Modern Pachinko
    Replies: 6
    Last Post: 06-03-2010, 04:39 PM
  5. motor on YJA, for shooter?
    By mudfud in forum Yahoo Japan - Auction Area
    Replies: 1
    Last Post: 11-16-2009, 11:21 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •