olympia evolution type "B"

[vinvinslot]

Hi Guys, this will be my first asking. Hello to everyone. I have a olympia evo type B. HOT ROD QUEEN (PROBLEM) tokens go strieght to the outside tray. insert metals is flashing,1 2 3 medals are lit. payout "0", credit "0"/-- if button is pressed for 5 seconds. When energising machine I dont here a click on the coin mech. How can I solve this and how can I check the clicking round coil with 2 wires to see if it is good. What do I clean the coin eye with alchol didnt work. Thanks in advance vinvinslot...

[Wayne-Ooo]

You should try a "Full Reset" of the machine.

Here's the steps, in the manual below.

Olympia Guide.jpgOlympia Guide 001.jpgOlympia Guide 002.jpgOlympia Guide 003.jpgOlympia Guide 004.jpgOlympia Guide 006.jpgOlympia Guide 007.jpgOlympia Machine.jpg

[vinvinslot]

Hi Thanks for the reply... I have tryed a full reset to no avail. I am looking at the round electro magnet on the coin mech -----HOW can I test it anyone out there knows???

[Card Shark]

Welcome to PachiTalk!

This just came up recently. I will see if I can find the post for you. Wayne-Ooo is great with advice on these machines. He has helped me out a lot.

[hanabi]

Hi Thanks for the reply... I have tryed a full reset to no avail. I am looking at the round electro magnet on the coin mech -----HOW can I test it anyone out there knows???

Welcome to PachiTalk!

This just came up recently. I will see if I can find the post for you. Wayne-Ooo is great with advice on these machines. He has helped me out a lot.

Think this may be the thread you're looking for?

Neo Planet T machine not accepting coins

[Wayne-Ooo]

The two wires you see going to it should have voltage.

You'll have to check and see if you have voltage going to it, with a multi-tester.

If the machine is up and running except for the magnet not coming in, (no error codes), then I'am guessing there isn't any voltage at the magnet or the magnet is bad. With your tester check the points where the two wires plug in. Also look to see if you have a bent pin or discolored pin in the connection.

If it all looks good and you have voltage there then check to see if you have voltage at the magnet. If so then the magnet is bad.

If there is not voltage at the connection then you most likely have a broken wire in the wiring harness, that connects to the door to the motherboard.

A simple fix, (till you find the problem or need to find a part), would be to hold the plate in, (that the magnet is suppose to be pulling in), and tape in down. The coin mechanism won't know the difference.

[vinvinslot]

Wayne, thanks but I closed the magnet,(taped it) yes the tokens are going to the proper hopper(inside) now but still no regestering of tokens to play game. HELPPPPPPPPPPPPPP

[vinvinslot]

Hi All, Anyone out there no where I can get parts for my OLYMPIA MACHINE type "B"???

[Card Shark]

Parts can be difficult to find. However, you have an absolutely amazing support group here. Can you maybe list the parts you are looking for and some pictures? I am sure someone will come along with more suggestions.

[vinvinslot]

Thanks CARD SHARK... The part I need is for a olym. evo. hot rod queen coin mech. electro magnet #SB 065 DC 22V 91124

[Wayne-Ooo]

If it is not registering tokens, and the sensors are not working either.

It sounds as if the machine is not reset or there is no voltage to the coin mechanism.

Each step in the reset procedure must be done exactly, or the machine doesn't reset. If you know for sure, that you have done the reset correctly, then I'd unplug the coin mechanism and check to see if you have voltage at the connection.

With the magnet not working and also not registering tokens, sounds as if there is no power at all at the coin mechanism.

[vinvinslot]

Wayne, Thanks again... There is power to coin mech./magnet from board. The plug in question 4 prong to coin mech. proper. What color wires is the proper test for activation? thanks in advance vin vinslot

[Wayne-Ooo]

Yes, it's a four wire plug.

Red, Brown, Yellow, Black wires.

If I remember, Black is ground, Yellow and Brown are the two sensors and Red is the magnet.

[Wayne-Ooo]

Ok, I went back and read your first post. You said "insert metals is flashing,1 2 3 medals are lit. payout "0", credit "0"".

My question is, Is the "Start" light also on?

What should happen after a reset is. The payout and credit windows would display 0, The insert medals light is flashing. You deposit 3 tokens and the 1, 2, 3 medals lights would light up, then the start light should light, after depositing those 3 tokens. Does this happen on your machine?

[vinvinslot]

Wayne, the start light is NOT on. also I noticed that on the plug to the main black box the last 2 wires are clipped (red &white) if that helps. Again thanks vinvinslot

[Wayne-Ooo]

Ok, I'am 99% sure it's not your coin mechanism. It just didn't make sense that voltage is there, but not working. The only reason it accepted tokens was because we taped down the magnet plate.

On the other hand I'am 99% sure that it's the spin lever. If the "Start" light is not lit, after depositing 3 tokens, the only reason would be that the spin lever is stuck on.

[vinvinslot]

Ok Wayne, tomorrow I will dismantle the spin lever, clean it with alcolhol. The lever does move so I will try electrics. I hope we can get to the bottom of this soon. THANKS vinvinslot

[Card Shark]

Wayne-Ooo is the best. You are in great hands.

I hope your machine is up and running soon.

[Wayne-Ooo]

Those two wires, (red&white), would have ran to 2 metal prongs that sensed a hopper overflow. It's not uncommon at all for these to be cut. It won't effect your machine, unless you were to touch them together. It would set off an error code "OF".

[Wayne-Ooo]

After sleeping on it, I'am thinking your Max Bet button or one of the other bet buttons may be stuck.

Please check those.