Page 2 of 3 FirstFirst 1 2 3 LastLast
Results 21 to 40 of 45

Thread: Bally's ProSeries Need help with issues!

  1. #21
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    I seated the reset chips all the way in, hold the reset and psuedo coin buttons and power on. all i'm getting now is all 9's flashing. What does this mean and what can I do?

  2. #22
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    I picked up a new battery, should I go ahead and solder it in?

  3. #23
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    well, after reading and talking to a couple people, i will pick up a battery with prongs already attached to it and solder that in!

    Anyway to bypass the battery usage? would it be by removing the pin to just 1 point?

  4. #24
    The Diceman Chrisdice's Avatar
    Join Date
    Sep 2005
    Location
    Seaford, Delaware, United States
    Posts
    3,358
    Thanks
    1,973
    Thanks Received
    3,979

    Default Re: Bally's ProSeries Need help with issues!

    you can't bypass the battery, changing the jumper is for keeping the board in storage so the battery doesn't drain.

    not sure what the 9's mean. make sure the chips are in the right spots and are facing the right way.
    Chris Dice
    Yo 11 any 7

  5. The following user says "Thanks" to Chrisdice


  6. #25
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    They are definetly in the right location's. I guess i can try rotating them to the other direction. Right now ive got to figure out out to get the new battery in there. Trying to find one close by that has tabs on it already!

    do you recommend a certain type of solder to use?

    Thank you!

  7. #26
    The Diceman Chrisdice's Avatar
    Join Date
    Sep 2005
    Location
    Seaford, Delaware, United States
    Posts
    3,358
    Thanks
    1,973
    Thanks Received
    3,979

    Default Re: Bally's ProSeries Need help with issues!

    any solder is fine. chips have a small nitch on them. the nitch will be on the top. and match to the picture on the board. if you did put them in backwards there is a good chance they might be fried.
    Chris Dice
    Yo 11 any 7

  8. The following user says "Thanks" to Chrisdice


  9. #27
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    Would it allow a reset if the battery was dead?

  10. #28
    The Diceman Chrisdice's Avatar
    Join Date
    Sep 2005
    Location
    Seaford, Delaware, United States
    Posts
    3,358
    Thanks
    1,973
    Thanks Received
    3,979

    Default Re: Bally's ProSeries Need help with issues!

    no
    Chris Dice
    Yo 11 any 7

  11. The following user says "Thanks" to Chrisdice


  12. #29
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    Found a battery with tabs on it on my lunch break! Hopefully the clear chips didn't fry, I will check the notch position on the chips tonight. The chips are labeled with the U12 and U15 on them and I assumed they went in with the text facing the same direction as the ones removed and all the others on the board. That's what happens when I assume, I make an ass out of u and me

  13. #30
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    i installed the battery and luckily the i had the reset chips in there the right way. when i power it on while holding the 2 buttons for a reset. It just shows 82 9 in the window. I dont see this error code in the manual.

    Any idears?! thanks!

  14. #31
    The Diceman Chrisdice's Avatar
    Join Date
    Sep 2005
    Location
    Seaford, Delaware, United States
    Posts
    3,358
    Thanks
    1,973
    Thanks Received
    3,979

    Default Re: Bally's ProSeries Need help with issues!

    check the jumper and also volt test the battery and make sure its good. 82 codes are normally battery related.
    Chris Dice
    Yo 11 any 7

  15. The following user says "Thanks" to Chrisdice


  16. #32
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    voltage is good and i had the jumper for the battery set to one prong, but when i set it to both, upon startup I get the all 9's. they stay on then go off every 2 seconds or so.

    i've tried pressing reset and it just comes back to the 9's again.

    Any ideas?!

  17. #33
    The Diceman Chrisdice's Avatar
    Join Date
    Sep 2005
    Location
    Seaford, Delaware, United States
    Posts
    3,358
    Thanks
    1,973
    Thanks Received
    3,979

    Default Re: Bally's ProSeries Need help with issues!

    are the 9's there with and without the reset chips? maybe the chips you have are no good. when you reset the game with the chips you should see a CL or PC in the display.
    Chris Dice
    Yo 11 any 7

  18. The following user says "Thanks" to Chrisdice


  19. #34
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    let me take them out and see. they are supposedly for a pro series 5500 ill replace them and find out.

  20. #35
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    After swapping out the chips for the originals. It showed CH P for a second then switched to the normal 83 F with everything flashing. (i did not change the clearram prong back to single when powering it on.)

    It's like it wants to reset!

    what shall I try next?

  21. #36
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    ok i dont know how or why, but with the reset chips out. I powered it on and voila it shows the correct codes and it reset! I was able to enter the setup and check out all the different options. I exited the setup and closed the door and its ready for play.. but coins just drop through.. my coin comparitor has an LED on it but its not lit up. any suggestions?!

    im still in shock it reset lol

  22. #37
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Default Re: Bally's ProSeries Need help with issues!

    in one of the tests I was able to see the coin comparitor light come on. I removed it and checked for any jams, but everything seems fine.

  23. #38
    Blind Shooter Mitchell's Avatar
    Join Date
    May 2010
    Posts
    85
    Thanks
    52
    Thanks Received
    47

    Smile Re: Bally's ProSeries Need help with issues!



    It works!! I forgot to switch on the coin mech

    Now it's on to getting all the lights working!

    Thank you so so so much for all the help!

  24. The following 5 users say "Thanks" to Mitchell


  25. #39
    Pachi Puro Moparformances's Avatar
    Join Date
    Jan 2009
    Location
    Diamond Springs CA
    Posts
    14,076
    Thanks
    26,525
    Thanks Received
    12,096

    Default Re: Bally's ProSeries Need help with issues!

    congrats to ya
    Never Doubt that a small group of thoughtful, .......... /........ If your not going to stand behind our troops
    ...committed people can change the world. ............. /.................Please, Please stand in front of them
    .....Indeed, it is the only thing that ever has............./
    .........................................Margaret Mead

  26. The following user says "Thanks" to Moparformances


  27. #40
    The Diceman Chrisdice's Avatar
    Join Date
    Sep 2005
    Location
    Seaford, Delaware, United States
    Posts
    3,358
    Thanks
    1,973
    Thanks Received
    3,979

    Default Re: Bally's ProSeries Need help with issues!

    glad you got it working!!!
    Chris Dice
    Yo 11 any 7

  28. The following user says "Thanks" to Chrisdice


Page 2 of 3 FirstFirst 1 2 3 LastLast

Similar Threads

  1. My new project! Bally's Bonus Times
    By Mitchell in forum Slot Machines | English Fruit Machines | Rotamints
    Replies: 31
    Last Post: 09-07-2010, 09:40 AM
  2. needs work - bally's coin 25Cents slot machine - $200 miami
    By SlotsRfun in forum FB Marketplace, Craig's List and Other Listings
    Replies: 0
    Last Post: 01-31-2010, 07:23 PM
  3. Looking for Advise/Info on a Bally's Slot
    By millermaster1 in forum Slot Machines | English Fruit Machines | Rotamints
    Replies: 19
    Last Post: 11-13-2009, 01:54 AM
  4. New User - Issues
    By Sid in forum Frequently Asked Questions about the Site
    Replies: 0
    Last Post: 07-20-2009, 05:11 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •